B – 02 Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes, aluminum alloy, aluminum-alloy drawn seamless tubes. ASTM B Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes. Drawn Aluminum Tubing from TW Metals is a magnesium and silicon alloyed aluminum product with good corrosion resistance and formability. Call now!.
|Published (Last):||3 January 2014|
|PDF File Size:||7.2 Mb|
|ePub File Size:||5.74 Mb|
|Price:||Free* [*Free Regsitration Required]|
T4, T42 H 0.
C For purposes of determining conformance to these limits, an observed value aastm a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit, in accordance with the rounding-off method of Practice E Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Asrm or that the aggregate of several Others elements exceeds the limit of Totalthe material shall be considered non-conforming.
Coiled tubes are generally available only as round tubes with a wall thickness not exceeding 0. ASTM does not give any warranty express or implied or make any representation that the contents of n210 abstract are accurate, complete or up to date.
The producer may analyze samples for trace elements not specified in the specification. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Alloy Alclad F O 0. The samples from finished tube shall not be required to conform to these limits.
Aluminum F O 0. When specified, b201 treatment of applicable tempers shall be in accordance with practice B Flattening test specimens shall be flattened sidewise under a gradually applied load so as to give a uniform radius of bend until the minimum outside diameter under load is not more than F times the wall thickness of the tube as specified.
Alloy Alclad F.
ASTM B210 Aluminum-Alloy Drawn Seamless Tubes Manufacturer
The tube shall be produced by drawing an extruded tube made from hollow extrusion ingot cast in hollow form or pierced and extruded by the use of the die and mandrel method. The tube shall conform to the tensile property requirements specified. This specification covers aluminum and aluminum-alloy drawn seamless tubes in straight lengths and coils for general purpose. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A for aluminum designation in accordance with Practice E E Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements.
F Other elements Total shall be the sum of unspecified metallic elements 0. Link to Active This link will always route to the current Active version of the standard. Historical Version s – view previous versions of standard.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. A Limits are in weight percent maximum unless shown as a range or otherwise stated.
asfm It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The tubes shall conform to the chemical composition requirements specified. B Analysis shall be made for the elements for which limits are shown in this table.
Tensile Strength, ksi Yield Strength D 0.
6061 Drawn Aluminum Tubing
Alloy F O 0. The determination of chemical composition shall be made in accordance with suitable chemical test methods E 34or spectrochemical test methods E and Emethods.
H The aluminum content shall be calculated by subtracting from The tension tests shall be made in accordance with test methods B M. This abstract is a brief summary of b21 referenced standard. Note 2—Throughout this specification, use of the term alloy in the general sense includes aluminum as well as aluminum alloy. I Alloy clad with Alloy J Composition of cladding alloy as applied during the course of manufacture.
ASTM B – 02 Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes
The different methods for leak testing of tubes are presented. However, such analysis is not required and may not cover all metallic Others elements.
Work Item s – proposed revisions of this standard.